|
Post by dragan on Nov 27, 2014 19:28:14 GMT
Mate I am from Macedonia and if I order this the postage will be OMG so if thare is somebody is kind enough and give me the measurements? Dragan
|
|
|
Post by fatblokeonbandit on Nov 27, 2014 20:12:58 GMT
Mate I am from Macedonia and if I order this the postage will be OMG so if thare is somebody is kind enough and give me the measurements? Dragan Oket dokey shipmate, remind me tomorrow when i can get to the garage
|
|
|
Post by dragan on Nov 27, 2014 20:13:47 GMT
Ok mate tomorrow
|
|
|
Post by captain chaos on Nov 27, 2014 20:35:05 GMT
|
|
|
Post by fatblokeonbandit on Nov 27, 2014 22:19:10 GMT
the little tappet twiddling tool
|
|
|
Post by dragan on Nov 28, 2014 13:38:05 GMT
Mate I am from Macedonia and if I order this the postage will be OMG so if thare is somebody is kind enough and give me the measurements? Dragan Oket dokey shipmate, remind me tomorrow when i can get to the garage Hi mate I am remaineding you for the measurement
|
|
|
Post by fatblokeonbandit on Nov 28, 2014 15:57:54 GMT
Just been out in the garage tape measure in hand and searched and searched, then realised its underneath my mates bandit engine, i will ring him to see if he has finished painting it.!, sorry matey, ill get the measurements as soon as i can
|
|
|
Post by dragan on Nov 28, 2014 18:41:46 GMT
Ok mate just please dont forget me. Thanks Dragan.
|
|
|
Post by fatblokeonbandit on Nov 30, 2014 16:01:19 GMT
and more info needed let me know matey
|
|
|
Post by dragan on Nov 30, 2014 18:37:12 GMT
and more info needed let me know matey
Thanks for the help and support mate. Only you screw the engine to the holder or you just put the engine on it?
|
|
|
Post by fatblokeonbandit on Nov 30, 2014 18:47:35 GMT
Just 10mm rods through the side and rear engine mountings
|
|
|
Post by dragan on Nov 30, 2014 20:41:17 GMT
Just 10mm rods through the side and rear engine mountings Thanks my friend and may force be with you.
|
|
|
Post by fatblokeonbandit on Nov 30, 2014 20:56:04 GMT
Just 10mm rods through the side and rear engine mountings Thanks my friend and may force be with you. Live long and prosper
|
|
|
Post by nw66 on Dec 7, 2014 17:42:12 GMT
Going back to original post aqua blasting is safest
|
|
terminator efe
Oviraptor
Posts: 7
Bikes: many cool things
Reg: Nov 5, 2014 21:47:22 GMT
|
Post by terminator efe on Dec 26, 2014 23:04:44 GMT
Hea guys happy new year to all now back to business and summer is coming,,, now back to blasting ure motor,,as mentioned above even the powder coaters use blasting to clean but never seem to care about bearing housing or oil galleries usually story ,,, I am based in mayo Ireland and can do soada bead and aggressive blasting which seems to be non exestiant around here but I'm a biker and try to cover all areas that all else are afraid off ''''''''' so its down to this and I have done my trial and error over the years so I,d like to think I know now,, SODA is super good but slow and not great at removing paint or grease,,, super fine glass bead is super good for (satin silver finish)and full removal of paint grease and all else,,, now any thing used after that is aggressive blasting this something most people can do and this can be deadly to ure motor,, now my point is after all these years of trying I think I should know now,,,, pj1 as mentioned before is super good x but I cant get here any more so I have to move on the biggest issus I have is that nitromores is shit wire brush is no better ,,nothing u do will LAST a season!!!! so blasting is key if the alloy(engine ) is keyed or etched from blasting then etch primer light 2k primer and 2K finish this process will last forever and is heat resistant and weather to '' so there u have it blasting in my opinion will properly key any alloy any with proper finising will last!!!!!!! I,m happy to advise on engines, carbs,calipers and all else u might consider blasting (there,s not much I can't blast )
|
|